Installation of treatment plants Even before building a house, it is necessary to decide on a wastewater treatment system. If it is not advisable or impossible to connect to a central wastewater treatment system, then biological wastewater treatment plants must be installed in a suitable location. It is best to install treatment plants near open water bodies, which reduces the cost of installing treatment plants. If there are none around, the treated technical water can be infiltrated into the ground or a reservoir for secondary use. The treatment plants we sell perform the highest level of wastewater treatment, operate quietly and do not emit an unpleasant odor. During treatment, nitrogen and phosphorus are removed from wastewater, which means that the water discharge points do not become overgrown with sludge, which is extremely important where there are infiltration fields behind the treatment plants. The wastewater treatment process uses microorganisms found in nature, so the wastewater treatment procedure is close to the natural purification that occurs in nature. Valyo device from above august-logo-w biomax-logo-w feliksnavis-logo-w svaiste-logo-w august-logo-w biomax-logo-w feliksnavis-logo-w svaiste-logo-w august-logo-w biomax-logo-w feliksnavis-logo-w svaiste-logo-w Installation of treatment systems Biological wastewater treatment systems are easy to install, easy to transport, and take up very little space. Often, buyers can install treatment devices themselves, but for the best result, it is worth relying on specialists in this field. In order for sludge to accumulate in the tanks more slowly, it is advisable to install a grease trap in front of the treatment device, which will collect primary impurities. Installation of treatment devices: how to choose the right place? Before starting house construction work, it is very important to decide what treatment system you will use at home. There are cases when it is not possible to connect to a central wastewater treatment system. Then you have to decide which device to choose and in which suitable place to install the wastewater treatment plant. The best place to choose is so that the treatment plant is closer to a body of water. Such a place to install the plant allows you to save on the cost of installing the treatment plant. However, if there are no bodies of water nearby, you can always infiltrate the treated water into the ground or a reservoir for further use of the treated water. Treatment plants allow you to perfectly reuse the treated water, thus saving good water. Installation of treatment plants, what does it look like? Installation of biological wastewater treatment systems is an easy process that is carried out in one working day. This plant is easy to transport, and it does not take up much space. Installation of treatment plants can also be carried out by customers themselves, but it is always recommended to entrust these works to specialists who are well versed in this work and have been doing it for many years. It is important to mention that during the installation of the plants, in order to slow down the accumulation of sludge, a grease trap should be installed, which will help to collect primary impurities. Installation of treatment plants: preparation Like everything else, wastewater treatment plants need to be prepared. What does this whole process look like? Installation of treatment plants begins with digging a pit. The depth of the pit depends on the type of treatment plant chosen. Before installing the treatment plant, it is important to make sure that the inlet and outlet pipes are working perfectly, have the right slope and depth. A very important detail in the installation of treatment plants is the upper part of the plant itself. It is important to make sure that this part is horizontal, because if it is not, then the plant will not fully do its job. After completing this work, the filling work continues. The filling of the plant takes place in stages, in order to strengthen the wastewater treatment plant itself as firmly as possible. It is poured with a 20-30 cm layer of sand and is fixed with a vibrating plate. At the same time, when the sand is poured, water is slowly poured into the plant. After filling the device with sand to the top, the lid is covered so that sand does not enter the inside of the wastewater treatment device when pouring sand later. After completing these works, the soil is poured up to the specified mark. There are cases when the installation of the treatment device becomes a little more complicated due to high groundwater. In this case, the device is anchored to the reinforced concrete foundation. The wastewater treatment device can be fixed with the help of stainless steel cables, or sand can be poured, which needs to be compacted. Later, it is mounted to the anchor plate.